Adafruit Feather RP2040 with RFM95 LoRa Radio – 915MHz – RadioFruit and STEMMA QT
The Adafruit Feather RP2040 with RFM95 LoRa Radio – 915MHz is a powerful and portable development board designed for wireless projects that need more range than Bluetooth or Wi-Fi. Adafruit combines the Feather RP2040 platform with an RFM95 LoRa radio module, creating a compact board that supports long-range packet communication while still offering the flexibility and ease of use of the Feather ecosystem. It is a smart solution for makers, developers, and engineers building remote sensors, IoT nodes, monitoring systems, and custom wireless networks.
At the center of the board is the RP2040 microcontroller, a dual-core 32-bit Cortex M0+ chip running at 133 MHz with 264 KB of RAM and 8 MB of onboard QSPI flash storage. Because of that, the board has enough processing power for LoRa and LoRaWAN applications that need reliable packet handling and efficient code execution. In addition, the board provides 21 GPIO pins, four 12-bit ADCs, two I2C interfaces, two SPI interfaces, two UART peripherals, and up to 16 PWM outputs.
This version uses a 900 MHz LoRa radio module that can be configured for either 868 MHz or 915 MHz operation in software. The radio is based on the SX127x family and communicates over SPI. It supports license-free ISM band use, offers selectable transmit power from +5 dBm to +20 dBm, and is designed for small packet communication over much longer distances than common 2.4 GHz wireless technologies. Adafruit notes that the board is not intended for audio or video transmission, but works very well for sensor data, control signals, and telemetry.
For portable use, the board includes a JST connector for a 3.7V lithium polymer battery and a built-in 200mA+ LiPo charger. It can also run directly from the USB Type-C port, and it automatically switches between USB power and battery power when needed. Moreover, it includes a built-in NeoPixel, a red status LED on pin 13, a STEMMA QT connector for solderless I2C peripherals, reset and bootloader buttons, a 3.3V regulator with 500mA peak current output, and four mounting holes for easier installation in custom builds.
The board also gives you flexible antenna options. You can solder a simple wire antenna to the dedicated pad, or use the built-in uFL connector with a larger external antenna for improved performance. Adafruit reports initial test results of over 1.2 miles, or about 2 kilometers, line-of-sight with quarter-wave wire antennas under default library settings. The board comes fully assembled and tested, and includes headers for soldering. However, a battery, USB cable, and antenna wire are not included. The board measures approximately 50.8mm x 22.8mm x 7mm and weighs about 6.3 grams.
Technical Details
- Measures 2.0″ x 0.9″ x 0.28″ (50.8mm x 22.8mm x 7mm) without headers soldered in
- Light as a (large?) feather – 6.3 grams
- RP2040 32-bit Cortex M0+ dual core running at ~133 MHz @ 3.3V logic and power
- 264 KB RAM
- 8 MB SPI FLASH chip for storing files and CircuitPython/MicroPython code storage. No EEPROM
- Tons of GPIO! 21 x GPIO pins with following capabilities:
- Four 12-bit ADCs (one more than Pico)
- Two I2C, Two SPI, and two UART peripherals, we label one for the ‘main’ interface in standard Feather locations
- 16 x PWM outputs – for servos, LEDs, etc
- Built-in 200mA+ lipoly charger with charging status indicator LED
- Pin #13 red LED for general purpose blinking
- RGB NeoPixel for full-color indication.
- On-board STEMMA QT connector that lets you quickly connect any Qwiic, STEMMA QT or Grove I2C devices with no soldering!
- Both Reset button and Bootloader select button for quick restarts (no unplugging-replugging to relaunch code)
- USB Type C connector lets you access built-in ROM USB bootloader and serial port debugging
- 3.3V Power/enable pin
- 4 mounting holes
- 12 MHz crystal for perfect timing.
- 3.3V regulator with 500mA peak current output
We squished all the parts on our Feather RP2040 over towards the USB port to make some room on the end. This Feather RP2040 LoRa Radio uses the extra space left over to add an RFM9x LoRa 868/915 MHz radio module. These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you need more range than 2.4 GHz (BT, BLE, WiFi, ZigBee).
Radio module specifications:
- SX127x LoRa® based module with SPI interface
- Packet radio with ready-to-go Arduino libraries
- Uses the license-free ISM bands (ITU “Europe” @ 433MHz and ITU “Americas” @ 900MHz)
- +5 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software)
- ~300uA during full sleep, ~120mA peak during +20dBm transmit, ~40mA during active radio listening.
- Simple wire antenna can be soldered into a solder pad, there’s also a uFL connector that can be used with uFL-to-SMA adapters for attaching bigger antennas.
Product Dimensions: 52.0mm x 23.0mm x 7.2mm / 2.0″ x 0.9″ x 0.3″
Product Weight: 6.3g / 0.2oz































