This server centralizes data and enables users to share and stream multimedia files to phones, tablets and other devices on a network. Ideal for workgroups, families, and single users. A wide variety of software is available to tailor the ODROID-HC4 to your specific needs. Upgrade the storage capacity of this server with one or two larger HDD/SSD. The HC4 is built with two high performance SATA port and a Gigabit Ethernet port, to build a faster network storage device, and also supports RAID configurations. The HC4 is designed to hold 2x 2.5 inch HDD/SSDs or 3.5inch HDDs in any combination.
A | CPU (Amlogic S905X3) | H | 2x System LED indicators |
---|---|---|---|
B | DDR4 memory (4GiB) | I | 1x UART for system console |
C | 2x SATA ports | J | 1x IR receiver |
D | 1x RJ45 Ethernet port (10/100/1000) | K | 5x GPIO pins (for optional OLED display) |
E | 1x HDMI 2.0 | L | 1x Micro SD slot |
F | 1x USB 2.0 host port | M | 1x Cooling fan |
G | 1x DC power jack (Outer diameter : 5.5mm, inner diameter 2.1mm) | N | 1x Boot switch |
KEY FEATURES
- Amlogic S905X3 Processor Quad-Core Cortex-A55 (1.8GHz)
- 4GB DDR4 RAM with 32-bit bus width (PC4-21333 grade)
- Dual SATA-3 port for 3.5inch and/or 2.5inch HDD/SSD storage
- UHS-1 capable micro-SD card slot for boot media
- Gigabit Ethernet port (RTL8211F)
- 1x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
- Digital audio over HDMI
- USB 2.0 Host
- UART serial console
- IR Receiver
- 1x DC Jack (5.5/2.1mm) rated for 14.5~15.5VDC
- 84 x 90.5 x 25mm
- 280g including heatsink, fan and case
SPECIFICATIONS
- Form Factor: Board Dimensions: 84mm x 90.5mm x 25.0mm
Heatsink Dimensions: 40mm x 32mm x 10mm
Weight: 280g including heatsink, fan and case - Processor: Amlogic S905X3 Processor
L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processors
Quad-Core Cortex-A55 (1.800GHz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz) - Memory: DDR4 4GiB with 32-bit bus width
Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design - Storage: 1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
- Networking: 1x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
- Realtek RTL8211F (Ethernet transceiver)
- LED indicators
- Green LED: Flashing by data traffics at 100Mbps connection
- Amber LED: Flashing by data traffics at 1000Mbps connection
- Video: 1x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
- Audio: 1x HDMI digital output
- Cooler: 1x Passive heatsink ( 40x32x10 mm ) on the CPU of PCB board
- 1x Hydraulic Bearing FAN
- Rated Voltage : 5V
- Rated Current : 100mA
- Max Speed RPM : 4,000
- Air Flow CFM : 4.3
- Air Pressure (In H2O) : 0.053
- Noise Level(dBA) : 23.9
- Dimension : 40 x 40 x 10.6 mm
- Wire & Connector : 80mm, 4 pin 1.25mm pitch
- 1x Hydraulic Bearing FAN
- External I/O: 1x USB 2.0 host port
1x Debug serial console (UART)
2x SATA Connectors - Other features: IR receiver for remote controller
System LED Indicators:- Red (POWER) – Solid light when DC power is connected
- Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
- Power: 1x DC jack: outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm
DC input: 14.5V ~ 15.5V- DC 15V/4A power adapter is recommended
Power consumption with two ST2000DM006 HDDs :
- IDLE(with HDD in spin-down) : ≃ 5.88W
- Active(using SAMBA): ≃ 15.59W
- Suspend: ≃ 0.29W
LINKS
- ODROID-HC4 Wiki Page: https://wiki.odroid.com/odroid-hc4/odroid-hc4
- How to install an operating system: https://wiki.odroid.com/odroid-hc4/getting_started/os_installation_guide
- Application notes: https://wiki.odroid.com/odroid-hc4/application_note/application_note
- Alternative heartbeat LED: https://wiki.odroid.com/common/application_note/external_connector/alternative_heartbeat_led
- OLED display how-to: https://wiki.odroid.com/odroid-hc4/application_note/oled
CERTIFICATIONS